Mitel Superset 4 User Manual Page 1

User Guide

-6- MAKING AND ANSWERING CALLS Make a call 1. Lift the handset. 2. If you want to use a Non-Prime Line, press a Line Appearance key. 3. Dial the num

-7- Speed Call Keys You may use Speed Call Keys to make a call or to send a string of digits during a call (press a Speed Call Key during a call to se

-8- Speed Call - Personal To dial a stored personal Speed Call number: 1. Lift the handset. 2. Dial 58. 3. Enter an index number between 00 and 09.

-9- CALL HANDLING Hold To place a call on Hold: zPress Hold. To retrieve a call from Hold: 1. Lift the handset. 2. Press the flashing line key. To

-10- Conference To form a Conference when a two-party call is already in place, or to add another party to an existing Conference: 1. Press TRANS/CONF

-11- Call Forward Call Forward lets you redirect incoming calls to an alternate number. Always redirects all incoming calls regardless of the state of

-12- Call Forward - I Am Here To forward calls from a remote station to your current location: 1. Press SUPERKEY. 2. Press # until "Call Forward

-13- Call Forward - End Chaining To ensure that calls do not get forwarded again by the destination number: 1. Lift the handset. 2. Dial 64. 3. Hang

-14- Messaging - Callback To leave a Callback Message on a telephone when you hear busy or ringback tone: z Press MESSAGE. To respond to a message wa

-15- Callback To request a Callback when you reach a busy or unanswered station: zPress the Callback feature key. To answer a Callback: zLift the han

Notice The information contained in this document is believed to be accurate in all respects but is not warranted by Mitel Networks® Corporation. The

-16- Campon To Campon to a busy station: zPress the Wait feature key. To retrieve a call when you hear Campon tone: zPress the Trade feature key. Do

-17- Direct Paging Direct Paging allows you to page a party through their telephone speaker. If the paged party has Off-Hook Voice Announce enabled, t

-18- Headset Operation (with Feature Control Switch) IMPORTANT NOTE: Mitel Networks Headsets with Feature Control Switch (PN9132-800-500-NA/9132-800-5

-19- Group Paging / Meet Me Answer Group Paging allows you to page a group of telephones through their built-in speakers. You can belong to to as many

-20- USING MLPP Multi-Level Precedence and Preemption (MLPP) facilitates emergency communications for the military. MLPP enables authorized users to s

-21- To answer a precedence call: If your telephone is idle and you receive a call with a precedence level higher than routine, you will hear the MLPP

-22- FEATURE ACCESS CODES Save Last Number **79Repeat Last Number Saved *6*Personal Speedcall - Invoke 58Personal Speed Call - Upper Range Index Nu

-i- Contents ABOUT YOUR PHONE1TIPS FOR YOUR COMFORT AND SAFETY2Don't cradle the handset! 2Protect your hearing 2Adjusting the viewing angle 2Cha

-ii- CALL HANDLING9Hold 9Transfer 9Conference 10Conference Split 10Swap 10Call Forward 11Call Forward - I Am Here 12Call Forward - End Chaining 13Call

-1- ABOUT YOUR PHONE The SUPERSET 4015 has eight fixed-function keys ( SUPERKEY, MESSAGE, HOLD, CANCEL, TRANSFER/CONFERENCE, REDIAL, , ) and seven per

-2- TIPS FOR YOUR COMFORT AND SAFETY Don't cradle the handset! Prolonged use of the handset can lead to neck, shoulder, or back discomfort, espec

-3-

-4- Changing Handsets Your SUPERSET 4015 telephone is compatible with several specialty handsets. To remove the handset shipped with your set from the

-5- Handset Receiver Volume Control To adjust the Handset Receiver Volume when you are using the handset: zPress or . Speaker Volume Control To adju