Mitel 5560 IPT none Specifications Page 106
- Page / 381
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Engineering Guidelines
92
AC Power adapters
For information on AC power adapters, refer to the appropriate Mitel phone data sheet.
In-Line Ethernet AC power adapters
A special In-Line Ethernet power adapter can provide local power feed to a wide range of
MiVoice IP Phones. Refer to Table 33 for details on which models support this powering option.
The power adapter plugs into a standard AC power outlet and has two RJ-45 connections, one
connecting to the network, and the other to the phone with power feed. Available units are
• 500002070 - 48 VDC Ethernet Power Adapter NA 120 V 50-60 Hz
• 500002080 - 48 VDC Ethernet Power Adapter UK 240 V 50 Hz
• 500002090 - 48 VDC Ethernet Power Adapter Europe 240 V 50 Hz.
In-Line Gigabit Ethernet AC power adapters
If the installer chooses to power the 5360 phone with a local in-line AC adapter, then the following
adapter must be used as it is the only adapter approved for use with the 5360 phone.
• 51015131: 802.3af 48VDC Gb Ethernet Power Adapter Universal, 100-240V 50-60 Hz
802.3af powering
Power over Ethernet technology allows devices such as IP Phones to receive power as well
as data over an existing Ethernet LAN infrastructure. The standard for Power over Ethernet is
IEEE 802.3af, and Mitel 5xxx series IP Phones conform to this standard.
Note 1: Refer to TeleMatrix 3000IP Technical documentation for details.
Note 2: For some IP Phone accessories or modules, the total power is not compatible with 802.3af LAN powering.
For details refer to the Gigabit Ethernet Installation Guide.
Note 3: Because Gigabit Ethernet wiring uses all cable pairs only Phantom 802.3af power can be used with the
Gigabit Ethernet Stand. Gigabit Ethernet End-span and Mid-span powering devices can be used if they are IEEE
802.3af compliant. Phantom power can be supplied over pairs (1, 2) and (3, 6) or over pairs (4, 5) and (7, 8).
Note 4: The UC360 must be powered from an IEEE 802.3at compliant PoE source, for details refer to the UC360
Engineering Guidelines.
Note: The standard 24 VDC power adapter has a 10 ft. (3 m) output power cord. If a
longer output power cord is required, you can use Part Number 57004243 (universal
AC input and output, 24 VDC, 15 ft. (4.5 m) power cord.
Note: Ensure that the Ethernet power adapter and its associated IP phone are
co-located.
Table 33: IP Phone Power Options (continued)
Phones
In-Line
Ethernet AC
Power
Adapter (48
VDC LAN)
AC Power
Adapter
(24 VDC)
Power
Dongle
(Cisco-Co
mpliant)
802.3af
Mid-Span
Power Hub
802.3af
Spare Pair
Power
802.3af
Signal
(Phantom)
Pair Power
802.3ab
(LLDP-MED
Signalling)
Support
Page 3 of 3
- MIVOICE BUSINESS 1
- Release 7.0 2
- All rights reserved 2
- Chapter 2: System Overview 3
- Chapter 5: Power 5
- Chapter 6: Performance 6
- Chapter 7: Applications 6
- Chapter 8: Emergency Services 7
- Chapter 9: IP Networking 7
- Chapter 10: Licensing 8
- Appendix A: CAT 3 Wiring 12
- Appendix D: VoIP and VLANs 13
- Appendix E: VoIP Security 13
- CHAPTER 1 15
- Overview 17
- About This Document 19
- System Management Tools 20
- Engineering Tool 20
- CHAPTER 2 21
- System Architecture 23
- MiVoice Business Controller 24
- Supported Countries 25
- CHAPTER 3 27
- System Configurations 29
- Multiple Units System 30
- Distributed System 30
- Hybrid System 32
- Standalone ACD Controller 36
- Network ACD Controllers 37
- ACD limits 37
- Basic Call Center 38
- Advanced Call Center 39
- Active agents vs. traffic 41
- Local agents vs. EHD agents 42
- Configuration Tables 44
- AX Controller 47
- CX/CXi Controller 49
- CX II/CXi II Controller 51
- MXe Controller 52
- Typical Configurations 53
- LX Controller 55
- Other Maximum Limits 57
- Use of SRTP 59
- HTML Applications on Sets 62
- Upgrading the System 63
- Provisioning System Resources 64
- CX Hardware Configurations 65
- Programmable Keys 68
- Provisioning for Traffic 70
- CHAPTER 4 73
- MiVoice IP Phones 75
- 5560 IPT Limits 76
- Phones Supported on the AX 77
- Micro Firewall 77
- NuPoint Unified Messaging 78
- SpectraLink Phones 79
- Phone Stands 79
- Gigabit Ethernet Phone Stand 81
- System Requirements 82
- Installation Recommendations 82
- Coverage and Capacity 82
- Typical operating range 84
- Range example 84
- RF Site Survey 85
- Other Considerations 85
- Access Connections 86
- MiVoice Business Console 87
- IP Sockets and Monitors 88
- Worked Example 95
- Phones and Voice Applications 97
- CHAPTER 5 99
- Introduction 101
- Installation Practices 101
- Controller Power Input 101
- MiVoice IP Phone Power 102
- Recommended Phone Powering 103
- Options for IP Phone Powering 104
- AC Power adapters 106
- 802.3af powering 106
- Third party 802.3af powering 108
- Powering the 5560 IPT 109
- Cable Power Loss 110
- Phone Power Consumption 110
- Engineering Guidelines 112
- Remote power 113
- LLDP-MED power advertisements 118
- System Power Requirements 122
- CHAPTER 6 125
- System Performance Index 127
- Performance with Ring Groups 130
- Performance with Hunt Groups 130
- CHAPTER 7 133
- 3300 ICP Applications 135
- Voice Mail 136
- Networked Voice Mail 136
- Embedded Music On Hold 137
- Application Processor Card 138
- CHAPTER 8 141
- Emergency Services 143
- Teleworker devices 145
- Other considerations 147
- CHAPTER 9 149
- IP Networking Considerations 151
- Clustering 152
- IP trunking models 154
- Variable RTP Packet Rates 157
- Route Optimization 158
- Automatic Route Selection 159
- SIP Trunking 160
- Applications compatibility 161
- Support for FAX over IP 161
- SIP aware firewall 162
- TCP/IP port usage 163
- Resiliency 164
- 911 emergency services 164
- CHAPTER 10 165
- System Licenses 167
- Device Licensing 172
- Licensing 173
- Licensing Limits 175
- Licensing Example 176
- CHAPTER 11 179
- Compression 181
- Bandwidth availability 185
- WAN bandwidth 186
- Bandwidth Management 187
- Zone Parent 189
- 1Root (WAN) 189
- 2 Root (WAN) 189
- 3Root (WAN) 189
- 1 Root (1) 191
- 2 Root (1) 191
- 3 Root (1) 191
- Deployment boundaries 192
- Additional information 193
- Codec – Introduction 194
- Codec selection 195
- Compression – Introduction 199
- IP Phones and compression 200
- Compression zones 202
- Compression and licenses 204
- CHAPTER 12 205
- Basic Concepts 213
- Packet loss 214
- Available bandwidth 214
- Packet priority mechanisms 214
- WAN connections 214
- Transcoding and compression 215
- Wideband voice 215
- LAN architecture 216
- VoIP Readiness Assessment 219
- Network Measurement Criteria 220
- Bandwidth Requirements 220
- Serialization Delay 221
- Codec Packet Rate 222
- 10 ms 20 ms 30 ms 40 ms 222
- G.729 102 122 142 162 222
- G.722.1 N/A 162 N.A 242 222
- Network Priority Mechanisms 223
- WAN layer 3 priority 227
- LAN QoS policies 231
- Full duplex network basics 232
- Half duplex network basics 233
- System Capabilities 234
- WAN traffic working example 235
- Firewalls and NAT 239
- CHAPTER 13 241
- Start-Up Sequence and DHCP 244
- Notes Regarding LLDP-MED 250
- Page 1 of 2 251
- 5302 Startup and DHCP 254
- DHCP Option Reclassification 255
- IP Phone behavior 256
- DHCP Lease Time 259
- 3300 TFTP Server 259
- CDP and VMPS 261
- Port Settings 263
- Release MCD 4.0 and 264
- Yes Basic STP 264
- MiVoice IP Phone 265
- Location change indication 265
- Use of VMPS with 3300 ICP 269
- Network Considerations 271
- SpectraLink wireless phones 272
- Mitel WLAN phones 272
- Wireless LAN considerations 273
- Coverage and capacity 274
- Connectivity to the wired LAN 274
- G.711 modem pass through 276
- T.38 FoIP Guidelines 277
- Signalling 278
- Operation 278
- Line Circuits and COS Options 279
- Resources required 280
- DSP provisioning 280
- Inter-zone default profile 281
- Intra-zone default profile 281
- Other intra-zone profiles 281
- Recommended settings 281
- T.38 Alarms 284
- 3300 IP Ports 285
- TCP / 443 (HTTPS) 289
- Enterprise 291
- IP Phone 294
- IP Console 295
- 5550-TKB 295
- IP Address Restrictions 299
- Cables and Connections 300
- Ethernet cable distances 301
- Straight and crossover cables 302
- Interconnection Summary 304
- APPENDIX A 305
- CAT 3 Wiring Practices 307
- CAT 3 Wiring 311
- APPENDIX B 313
- Basic Rules 315
- Define the IP Addressing 316
- Define the VLAN 316
- Example Network Topology 317
- Switch# configure terminal 318
- Switch1(config-vlan)# exit 318
- Router 1 configuration 322
- Programming the IP addresses 323
- Programming static routes 323
- Create Class Maps 324
- Create the Policy Maps 324
- Router 2 configuration 325
- Miscellaneous 328
- APPENDIX C 331
- LLDP, LLDP-MED Overview 333
- Defining voice VLAN and ports 336
- Ensure that LLDP is enabled 340
- Additional Useful Commands 341
- APPENDIX D 345
- When to use VLANs? 347
- Network Configurations 347
- Standalone CXi, voice only 348
- APPENDIX E 351
- Data Encryption 353
- Signalling and media paths 354
- Signalling security 355
- Data encryption support 357
- VoIP Security 359
- Dual Port Phones 360
- IEEE 802.1X 360
- Devices that support 802.1X 362
- Worm and virus protection 363
- Prevention of toll abuse 363
- SIP Security 364
- Glossary 365
Related products and manuals for IP phones Mitel 5560 IPT none
IP phones Mitel 5220 User Manual
(1 pages)
(1 pages)
© 2020, manymanuals.com. All rights reserved. | 1.697 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals